Thanks!jeaton01 wrote:Looking good, Mike.
Medic's Demon
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
The second wing half is attached now. This one will need some putty at the wing roots as well.
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Re: Medic's Demon
That's looking great Mike!
Stuart Templeton 'I may not be good but I'm slow...'
My blog: https://stuartsscalemodels.blogspot.com/
My blog: https://stuartsscalemodels.blogspot.com/
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
Thanks Stuart!
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
I was going to fit the rudder but the fit is bad, especially at the top. I added a piece of strip styrene that I'll trim to the rudder. Please ignore the mess on the rudder. That'll be cleaned up later.
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
Added the PE to the outside of the airbrakes. The PE is pretty thick, so this will be glued in stages.
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
Started on the gear as well. Wheels are being painted and the gear legs assembled. I dry fitted the gear legs to check and see if I got both wings at the correct angle. Yep! Good to go!
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Re: Medic's Demon
Looking very good! Gear looks great.
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..
- Medicman71
- Elite Member
- Posts: 9823
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: Medic's Demon
Thank you sir!
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Re: Medic's Demon
Yeah... Good fit on that rudder... not!
Great work thus far Mike!
Great work thus far Mike!
Stuart Templeton 'I may not be good but I'm slow...'
My blog: https://stuartsscalemodels.blogspot.com/
My blog: https://stuartsscalemodels.blogspot.com/