UH-1C Huey Gunship "Special Nose Art Edition"

Post your work in progress of your aircraft builds in here.
User avatar
Stikpusher
Moderator
Posts: 21558
Joined: Sat Apr 05, 2014 8:37 pm
Location: Ceti Alpha 5

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by Stikpusher »

keavdog wrote: ↑Wed Nov 11, 2026 9:50 pm That's better Tom. Hit him with a clear flat and you're good.
I’d suggest a red brown wash on the flesh areas for a more natural tone. Followed by some very light dry brushing on highlight areas such as the raised areas of the face and hands…

This figure is washes and dry brushing. Although in this case I used oils for the washes, and the. once those are cleaned up, it was enamels for the dry brushing.

Image
"Surely I have made my meaning plain? I intend to avenge myself upon you, Admiral. I have deprived your ship of power, and when I swing 'round, I intend to deprive you of your life."

FLSM
User avatar
BlackSheep214
Elite Member
Posts: 13800
Joined: Sun Apr 06, 2014 8:47 pm

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by BlackSheep214 »

What color did you use for fleas? I’ve always thought flesh color was too orangey to my eyes. That’s why I used Sail color by Gunze.
“Who controls the skies, controls the fate of this Earth”

Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney

“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
User avatar
Stikpusher
Moderator
Posts: 21558
Joined: Sat Apr 05, 2014 8:37 pm
Location: Ceti Alpha 5

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by Stikpusher »

BlackSheep214 wrote: ↑Thu Nov 12, 2026 4:17 pm What color did you use for fleas? I’ve always thought flesh color was too orangey to my eyes. That’s why I used Sail color by Gunze.
I started out with a color made my Testors in an acrylic set. I don’t think that they make the set anymore.

Image

Then a wash of burnt Sienna to give a reddish tone

Image

Last was the dry brush highlights
"Surely I have made my meaning plain? I intend to avenge myself upon you, Admiral. I have deprived your ship of power, and when I swing 'round, I intend to deprive you of your life."

FLSM
User avatar
BlackSheep214
Elite Member
Posts: 13800
Joined: Sun Apr 06, 2014 8:47 pm

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by BlackSheep214 »

Back on track… I have a tendency to assemble stuff out of step or skip on certain spots but instead glue to canopy. Example…roof nd inside column are to be assembled to cockpit area. Nope… I gotta do things the hard way/easy way. I glued the columns inside the chopper walls, the roof on one half of chopper body.

I opt to have the rotor engine door closed. I made some shims using very thin sheet pieces of styrene to help glue it flushed. Didn’t think whether it will interfere with gluing the body halves together. Testing whether it does or not… yeah a little bit but I think I can make it work.

Now what’s happened so far… tried to close up the chopper bodies together only to find some fit issues (most likely from my stupidity :headbang: ). Right now, I use thin CA a glue to close up the nose end first. Then, I’ll proceed with top and bottom body areas. So I figure, let me work slowly; glue little sections at a time using CA glue. Once the main body halves are done, the tail part shouldn’t be an issue.

I’m leaving off the rotor motor/blade install until last. I can’t risk breaking off delicate parts.
“Who controls the skies, controls the fate of this Earth”

Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney

“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
User avatar
BlackSheep214
Elite Member
Posts: 13800
Joined: Sun Apr 06, 2014 8:47 pm

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by BlackSheep214 »

I fought this one for an hour. Definitely serious fit issues trying to button up the canopy to fuselage halves. I had th remove the padded roof off the fuselage half top. CA glued it to cockpit assembly, minus the posts. The post go exactly where it's suppose to be...inside fuselage halves. Even though instruction guide says to glue to cockpit back side, they will not sit flush to fuselage.

A lot of fighting, sanding with dremel tool, checking the fit over and over until I'm sort of satisfied. The bottom has gaps and some shim work is next. No matter how hard I try to mate the bottom, it refuses to catch hold. It catches hold when I test fit no problem without cockpit floor installed. Go figure.


Image
All clear parts has to be installed from the inside. Havent installed front windshield, top windows or nose bottom windows. Top windows needs to be painted clear green first.

Here I'm thinking this one is gonna be a fun build. Instead, it's giving me headaches with fit issues.
“Who controls the skies, controls the fate of this Earth”

Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney

“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
User avatar
BlackSheep214
Elite Member
Posts: 13800
Joined: Sun Apr 06, 2014 8:47 pm

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by BlackSheep214 »

Headed to my bench early this morning before going to work. So far, it's good after I took off all the tape and clips.. Had to reglue one spot.
“Who controls the skies, controls the fate of this Earth”

Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney

“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
User avatar
Stuart
Elite Member
Posts: 12203
Joined: Sun Apr 06, 2014 1:06 pm
Location: North Wales

Re: UH-1C Huey Gunship "Special Nose Art Edition"

Post by Stuart »

Sounds like a challenging Assembly Tom but I'm glad to hear it all looks good this morning!
Stuart Templeton 'I may not be good but I'm slow...'
Post Reply

Return to “Aircraft Work in Progress”