Page 53 of 121
Re: Bolleken's 1:72 stuff
Posted: Fri Nov 17, 2017 3:52 am
by Bolleken
speedgraflex wrote:Marius, looks great! What are you using to fill the gaps? I am not sure what it is! Thanks.
In that case I used Revell Plasto filler, Mr. Surfacer by Gunze and Revell Aqua Paint applied with brush. The Auqas are usually very thick so you can use it as filler.
The canopies are now ready and sealed with Future.
My Viggen is acompanied by three other kits ready for painting. Viggen's NMF will be a challenge due to its dull look.
Re: Bolleken's 1:72 stuff
Posted: Fri Nov 17, 2017 11:07 am
by speedgraflex
I sincerely appreciate these images as I have never used Future before. I have the somewhat old fashioned notion that any clear coat runs the risk of yellowing over time. I have not been so willing to let go of this notion yet, but when I see your effort I am tempted! And appreciative! But part of me thinks Future is not to be trusted. My father instilled this prejudice when he refused to put certain chemical combinations in my mother’s kitchen (He was a Materials Testing specialist for a Swiss firm based in the U.S.). He also suggested to me more than once that hard floor wax was more effective than exotic Carnubas! He also tested every cup for lead as well...
Re: Bolleken's 1:72 stuff
Posted: Fri Nov 17, 2017 11:39 am
by Bolleken
I have been using Future Floor Finish since 2003 in every model. Here in Germany it is a kind of magical potion. Never made any bad experience with that. You can trust me.
Re: Bolleken's 1:72 stuff
Posted: Fri Nov 17, 2017 11:46 am
by speedgraflex
Mephisto! I mean Marius! Of course I trust you!! Haha! I needed your sense of humor after a rather grim week! Thank you, my friend.
Re: Bolleken's 1:72 stuff
Posted: Fri Nov 17, 2017 1:45 pm
by Duke Maddog
Superb work on those canopies Marius! They came out better than I expected. I also use Future to dip all my canopies in and have never had any issues with it yellowing. Some other clearcoats however.....
Re: Bolleken's 1:72 stuff
Posted: Fri Nov 17, 2017 4:17 pm
by Stikpusher
I was curious about how you were going to deal with the canopies. Polished and then Futured? Well that sure cleaned up that problem.
Bruce, I have been using Future for many many years now, (20 or so, rough guess) and like Mark said, no yellowing issues over the years. At least not yet. Now Testors rattle can clear coats on the other hand, I avoid that stuff like the plague.
Re: Bolleken's 1:72 stuff
Posted: Sat Nov 18, 2017 8:09 am
by dmminiatures
Speed - All I can say right now about this thread is IMPRESSIVE. the way you handled "nothing into something" is just WOW.
Re: Bolleken's 1:72 stuff
Posted: Sat Nov 18, 2017 11:28 am
by speedgraflex
Hey DM — just to clarify a very important point — it’s Bolleken’s amazing work here! Bolleken is the model builder. I just ask a lot of questions and make comments here with the other members like Duke and Stikpusher whose advice has been very helpful to me.
Your words of praise must be directed to Bolleken, though. Thanks in advance.
Bruce/speedgraflex
Re: Bolleken's 1:72 stuff
Posted: Sat Nov 18, 2017 8:21 pm
by dmminiatures
Much thanks for the correction, Bruce.
hats off to Bolleken!
Monty
Re: Bolleken's 1:72 stuff
Posted: Sun Nov 19, 2017 2:22 am
by speedgraflex
dmminiatures wrote:Much thanks for the correction, Bruce.
hats off to Bolleken!
Monty
Hats off to you as well, Danumurthi! I will call you Monty from here on out but at least once I wanted to be on good footing. Thank you so much!
Bruce