1/72 Zvezda Hind E finished
Posted: Sat May 06, 2017 9:36 am
Time for another batch!!!
I assume the first plastic has been cut and glued?
Page 1 of 3
Re: 1/72 Zvezda Hind E
Posted: Sat May 06, 2017 9:45 am
Two kits. Same kit number and type. Two different box sizes...
I assume the first plastic has been cut and glued?
I assume the first plastic has been cut and glued?
Re: 1/72 Zvezda Hind E
Posted: Sat May 06, 2017 11:02 am
ENEMY AIR!!! ENEMY AIR!!!
Are these the next group therapy for us?
Are these the next group therapy for us?
Re: 1/72 Zvezda Hind E
Posted: Sat May 06, 2017 11:30 am
Both same/same....I got the smaller boxed one from...Thomas_M wrote:Two kits. Same kit number and type. Two different box sizes...
I assume the first plastic has been cut and glued?
Squadron or Sprue Bros. The bigger box came from Ukraine. The seller even included a Ukrainian "dollar"!Yah, sure!!!Stikpusher wrote:ENEMY AIR!!! ENEMY AIR!!!
Are these the next group therapy for us?
I'm half tempted to throw in the "A" (green house) version as well....but not highly likely!
Re: 1/72 Zvezda Hind E
Posted: Sat May 06, 2017 1:57 pm
Re: 1/72 Zvezda Hind E
Posted: Mon May 08, 2017 4:14 am
I think i'll receive the A version next week, then follow for tipsFermis wrote:Both same/same....I got the smaller boxed one from...Thomas_M wrote:Two kits. Same kit number and type. Two different box sizes...
I assume the first plastic has been cut and glued?
Yah, sure!!!Stikpusher wrote:ENEMY AIR!!! ENEMY AIR!!!
Are these the next group therapy for us?
I'm half tempted to throw in the "A" (green house) version as well....but not highly likely!
The boxes differences are about the new zvezda package (larger are the late type).
Re: 1/72 Zvezda Hind E
Posted: Sun Jun 25, 2017 7:27 pm
Been a long time, but I finally got somewhere with these...
Pretty much nothing but the area where the rotor mounts will be visible. There's a good amount of detail, that could easily be enhanced, if one was so inclined to open up some panels...I am not!
Pretty much nothing but the area where the rotor mounts will be visible. There's a good amount of detail, that could easily be enhanced, if one was so inclined to open up some panels...I am not!
Re: 1/72 Zvezda Hind E
Posted: Sun Jun 25, 2017 8:34 pm
Every time I see the way you paint a cockpit, I want to send you mine, lol. Helicopters are yet to grab hold of my modeling mind, but your work gets me very excited by the possibilities in 1/72.
Re: 1/72 Zvezda Hind E
Posted: Mon Jun 26, 2017 3:56 am
Excellent work as usual Fermis 
I can recommend about fuselages to not follow instruction sequence. Imho best way is to glue half fuselages together (nose and tail) before final assembly
I can recommend about fuselages to not follow instruction sequence. Imho best way is to glue half fuselages together (nose and tail) before final assembly
Re: 1/72 Zvezda Hind E
Posted: Mon Jun 26, 2017 5:02 am
Thanks guys!
That is definitely my plan, as the setup they have never seems to work out great(with any kit). I've already discovered that I'm going to have to do a little trimming somewhere, as the fuselage halves don't quite meet up around the engine area.BsYamato wrote:Excellent work as usual Fermis
I can recommend about fuselages to not follow instruction sequence. Imho best way is to glue half fuselages together (nose and tail) before final assembly