X-35A, Revell, 1/48 FINISHED
-
speedgraflex
- Moderator
- Posts: 11358
- Joined: Fri Feb 10, 2017 11:08 pm
- Contact:
Re: X-35A, Revell, 1/48
Beautiful work! The minimalist approach lets the design shine most of all. Truly; a beautiful build of an important subject. Cheers.
Make more models!
-
Stikpusher
- Moderator
- Posts: 21188
- Joined: Sat Apr 05, 2014 8:37 pm
- Location: Ceti Alpha 5
Re: X-35A, Revell, 1/48
Thank you Bruce. A few more things to do and I can call this done.
"Surely I have made my meaning plain? I intend to avenge myself upon you, Admiral. I have deprived your ship of power, and when I swing 'round, I intend to deprive you of your life."
FLSM
FLSM
Re: X-35A, Revell, 1/48
Great stuff Carlos - that does look good!
Stuart Templeton 'I may not be good but I'm slow...'
-
BlackSheep214
- Elite Member
- Posts: 13417
- Joined: Sun Apr 06, 2014 8:47 pm
Re: X-35A, Revell, 1/48
Now put some legs on her! 
“Who controls the skies, controls the fate of this Earth”
Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney
“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney
“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
-
Stikpusher
- Moderator
- Posts: 21188
- Joined: Sat Apr 05, 2014 8:37 pm
- Location: Ceti Alpha 5
Re: X-35A, Revell, 1/48
Stuart, thank you.
Tom, we’re not quite yet at the point of getting the gear legs on. But soon I will be...
Tom, we’re not quite yet at the point of getting the gear legs on. But soon I will be...
"Surely I have made my meaning plain? I intend to avenge myself upon you, Admiral. I have deprived your ship of power, and when I swing 'round, I intend to deprive you of your life."
FLSM
FLSM
-
Medicman71
- Elite Member
- Posts: 11299
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: X-35A, Revell, 1/48
Very nice! Getting closer to the end with this one!
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
-
Stikpusher
- Moderator
- Posts: 21188
- Joined: Sat Apr 05, 2014 8:37 pm
- Location: Ceti Alpha 5
Re: X-35A, Revell, 1/48
So I mentioned earlier that I was going to add one more thing to this build and this is it...
The kit provides a single clear piece bubble canopy. But the actual X-35 had a two piece canopy, with a bow frame separating the windscreen and a side opening hood. So this is how I set about correcting that. I was not sure about the exact location of where to modify , so I had to wait until I had glued the canopy in place for a solid reference point. I used Epoxy for this to insure that canopy would not move and let that dry overnite. Of course this provides a rock solid attachment, and it did not fog the Future dipped clear part. Then after looking at photos, I found good reference points with the IP top and used them to guide me in scribing a split line into the canopy.
Then I finished masking the canopy to match the framing in photos. One side has a wider frame than the other. I also had to putty the front of the canopy to eliminate a step
And then I cleaned up the filler work
I then built up several layers of primer and paint to create something of a raised frame. In hindsight I should have used some black in a layer somewhere to lessen the chance of translucency. The primer and paint worked pretty well, but not 100% perfect.
The end result...
Tomorrow I should have this all finished...
The kit provides a single clear piece bubble canopy. But the actual X-35 had a two piece canopy, with a bow frame separating the windscreen and a side opening hood. So this is how I set about correcting that. I was not sure about the exact location of where to modify , so I had to wait until I had glued the canopy in place for a solid reference point. I used Epoxy for this to insure that canopy would not move and let that dry overnite. Of course this provides a rock solid attachment, and it did not fog the Future dipped clear part. Then after looking at photos, I found good reference points with the IP top and used them to guide me in scribing a split line into the canopy.
Then I finished masking the canopy to match the framing in photos. One side has a wider frame than the other. I also had to putty the front of the canopy to eliminate a step
And then I cleaned up the filler work
I then built up several layers of primer and paint to create something of a raised frame. In hindsight I should have used some black in a layer somewhere to lessen the chance of translucency. The primer and paint worked pretty well, but not 100% perfect.
The end result...
Tomorrow I should have this all finished...
"Surely I have made my meaning plain? I intend to avenge myself upon you, Admiral. I have deprived your ship of power, and when I swing 'round, I intend to deprive you of your life."
FLSM
FLSM
Re: X-35A, Revell, 1/48
Ahhhhhh - Now it makes sense! Great stuff Carlos, This is really coming on!
Stuart Templeton 'I may not be good but I'm slow...'
-
Stikpusher
- Moderator
- Posts: 21188
- Joined: Sat Apr 05, 2014 8:37 pm
- Location: Ceti Alpha 5
Re: X-35A, Revell, 1/48
Glad you like it. I figured that it would be much easier to explain with photos after it was all done.
"Surely I have made my meaning plain? I intend to avenge myself upon you, Admiral. I have deprived your ship of power, and when I swing 'round, I intend to deprive you of your life."
FLSM
FLSM
Re: X-35A, Revell, 1/48
Well, I was close. Sort of. Looks good.
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..