You've made a good start too, glad to see that! Keep it up ol' chap. 
ICM 1/48 C-45 Expiditor
-
Gary Brantley
- Elite Member
- Posts: 2739
- Joined: Tue Apr 08, 2014 9:40 pm
- Location: Cameron, Texas
Re: ICM 1/48 C-45 Expiditor
I like this project Lyle! You've made a good start too, glad to see that! Keep it up ol' chap.
You've made a good start too, glad to see that! Keep it up ol' chap. 
Re: ICM 1/48 C-45 Expiditor
thanks, Gary. Man, I'm rusty, corroded and about half-working. Sheesh.
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..
-
Gary Brantley
- Elite Member
- Posts: 2739
- Joined: Tue Apr 08, 2014 9:40 pm
- Location: Cameron, Texas
Re: ICM 1/48 C-45 Expiditor
Hey, you've just described me most of the time. Rest o' the time, I'm barely movin'! 
And of course, you're quite welcome !
And of course, you're quite welcome !
Re: ICM 1/48 C-45 Expiditor
Three doc appts this month...eye (Friday), hand (19th) and cardiologist (23rda). life is good.
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..
Re: ICM 1/48 C-45 Expiditor
I need some hep. in the image above, notice that the outside of the cowling and the nose piece seem to be a "not aluminum" color. A gray, perhaps or simply aluminum (alyouminnieyum for you Brits) that has oxidized? I'm likely wrong, but leaning towards it being a gray. This picture is from the KYANG archives, so I do not think it has been colorized.
Also, notice the landing/taxi light in the nose. Seems to be to the starboard side, eh? So, is it one, off-center or two -one each side?
How big are the KY letters on the fuselage? I'm thinking 12" since they are the same size as the bar on the insignia.
Can anyone make out the tail number more better than I? I think it is 20893. Any way to look up this number?
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..
-
Medicman71
- Elite Member
- Posts: 11299
- Joined: Mon Apr 07, 2014 9:32 am
- Location: Houston, Tx
Re: ICM 1/48 C-45 Expiditor
The nose is definitely gray. But I think the cowlings are dull aluminum (maybe). Also I think the inside upper cowling is painted black as an anti-glare measure. And there are two lights in the nose.
Mike
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Sponsored by Boeing, Lockheed Martin, Northrop Grumman, Saab, BAE, and Dassault
Re: ICM 1/48 C-45 Expiditor
Nice subject! I agree with Doc about the grey nose and black on the inside quarters of the engine cowlings. I think the cowlings are close enough to the engines to be Neutral Grey as well. Tail number is definitely 20893. The KY code looks to be slightly larger than the bar.
John aka JKim
-----------<><
-----------<><
Re: ICM 1/48 C-45 Expiditor
Mike and John, thanks! That is a gorgeous picture...this craft is USAF nor ANG, though. Sticking With the 20893. Ive fired off an email to MSgt Speck at the KYANG.
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..
Re: ICM 1/48 C-45 Expiditor
The similarities in serial number was suspicious so I did some digging.
According to the following document:
Page 172...
USAF 210893 was, at one point, "del. to Kentucky ANG 165th Fighter Bomber Squadron".
The photo I posted is the same aircraft as yours. Code is 210893.
Link to document:
https://www.goodall.com.au/beech18-prod ... part-3.pdf
According to the following document:
Page 172...
USAF 210893 was, at one point, "del. to Kentucky ANG 165th Fighter Bomber Squadron".
The photo I posted is the same aircraft as yours. Code is 210893.
Link to document:
https://www.goodall.com.au/beech18-prod ... part-3.pdf
John aka JKim
-----------<><
-----------<><