The difficult part is still ahead, attaching the wing. This is always difficult on a parasol wing aircraft. And this being an 25+ year old kit I do expect the fit to be "needing some adjustment". But that is the fun of building these old kits.portman wrote:That's looking lovely Borg - this'll look really nice when built up!
I do like the inter-war stuff, I really must have a go at something from that era myself.
ZTS Plastyk RWD-8 1/72
Re: ZTS Plastyk RWD-8 1/72
Re: ZTS Plastyk RWD-8 1/72
As suspected, the honeymoon is over. Fitting of the wing was difficult. I only did the middle struts and will work my way from middle to centre.
I used styrofoam, toothpicks and rubber bands for a jig.
I used styrofoam, toothpicks and rubber bands for a jig.
Re: ZTS Plastyk RWD-8 1/72
There is some engineering in that jig construction!
Looking still great!
- Kari
Looking still great!
- Kari
---
On the bench:
MiniArt 1:48 - Junkers F13 Float Plane
https://www.facebook.com/GrundAsk-Scale ... 721218708/
On the bench:
MiniArt 1:48 - Junkers F13 Float Plane
https://www.facebook.com/GrundAsk-Scale ... 721218708/
Re: ZTS Plastyk RWD-8 1/72
KSaarni wrote:There is some engineering in that jig construction!
Looking still great!
- Kari
I agree - that's a good method of jigging that I've not seen before.It's a lovely looking build Borg - very colourful - and I love the shark table mat!
Stuart Templeton 'I may not be good but I'm slow...'
-
mustang1989
- Moderator
- Posts: 5035
- Joined: Tue Mar 18, 2014 8:35 pm
Re: ZTS Plastyk RWD-8 1/72
That's quite a set up you've got there Borg! You've almost booby trapped it to where you've gotta be careful when you're pickin' that one up!! lol
Re: ZTS Plastyk RWD-8 1/72
by this point, i'd be using a 3 pound hammer to rig it.
To make each build less crappy than the last one. Or, put another way, "Better than the last one, not as good as the next one!"..
Re: ZTS Plastyk RWD-8 1/72
The shark table mat is my kid's but if it protects the table it is good enough.portman wrote:KSaarni wrote:There is some engineering in that jig construction!
Looking still great!
- Kari
It's a lovely looking build Borg - very colourful - and I love the shark table mat!
As for the jigging method. I think this only works on single wing aircraft but styrofoam with pins is easy to set up and adjust.
Re: ZTS Plastyk RWD-8 1/72
The jig did not work properly. The rubber bands snapped and now the wing is crooked. But I have chosen not the adjust it. I think that snapping it off an reattaching it will not make it better and result in glue staines.
Most explicit view, you can see the difference between the wing and the tail plane.
Most explicit view, you can see the difference between the wing and the tail plane.
-
BlackSheep214
- Elite Member
- Posts: 13412
- Joined: Sun Apr 06, 2014 8:47 pm
Re: ZTS Plastyk RWD-8 1/72
If that happened to me, I can guarantee that damn kit would introduced to a nearby wall in 2 seconds. Hmm.. are you sure it's not the tail wings that's off center? I don't know but the main wings looked fine to me from the pic you posted.
“Who controls the skies, controls the fate of this Earth”
Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney
“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney
“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
Re: ZTS Plastyk RWD-8 1/72
Yeah it looks ok to me when you compare it to the fin - it's the tailplane that looks sightly off...BlackSheep214 wrote:If that happened to me, I can guarantee that damn kit would introduced to a nearby wall in 2 seconds. Hmm.. are you sure it's not the tail wings that's off center? I don't know but the main wings looked fine to me from the pic you posted.
Either way it looks great!
Stuart Templeton 'I may not be good but I'm slow...'