Plenty of room...I know this bench!!!Stikpusher wrote:Four!? Good thing they are 1/72... or you're gonna run out of bench space real quick...
Quadruple Jet Threat (Finished!)
Re: Quadruple Jet Threat
Re: Quadruple Jet Threat
Started with the 18's.
Not a whole special going on with these.
The bad thing about these kits is that there's no intake trunk...just half a wall(where the gear bays are) not very far back in there.
So...FOD covers to negate that issue!
Heated up some sheet styrene over a candle and pressed it over the intakes...
Those have been cut to the proper size and set aside for now...we'll see those again later.
On to the 14.
For the nav lights and tail beacon, the kit provides these in clear parts...but Those parts never seem to fit nicely, so I didn't even bother trying. I heated some clear sprue, dabbed a bit of CA, and smashed the heated end into the slot.
I used a grinding bit to grind em down close, finished off the rest with sand paper.
Tail beacon got the same treatment.
And...the A-6.
Again, not a whole lot of special treatment.
The rear deck of the pit, however...is a bit simple.
(started cutting out the detail, then thought I should do a before/after shot!)
Kit part..
After modification...
Not a whole special going on with these.
The bad thing about these kits is that there's no intake trunk...just half a wall(where the gear bays are) not very far back in there.
So...FOD covers to negate that issue!
Heated up some sheet styrene over a candle and pressed it over the intakes...
Those have been cut to the proper size and set aside for now...we'll see those again later.
On to the 14.
For the nav lights and tail beacon, the kit provides these in clear parts...but Those parts never seem to fit nicely, so I didn't even bother trying. I heated some clear sprue, dabbed a bit of CA, and smashed the heated end into the slot.
I used a grinding bit to grind em down close, finished off the rest with sand paper.
Tail beacon got the same treatment.
And...the A-6.
Again, not a whole lot of special treatment.
The rear deck of the pit, however...is a bit simple.
(started cutting out the detail, then thought I should do a before/after shot!)
Kit part..
After modification...
Re: Quadruple Jet Threat
As they sit right now...
18F...(color PE)
14...(brush painted)(this Aires pit was a NIGHTMARE to make fit!)
A-6...(brush painted)
I'll do the seats later.
18F...(color PE)
14...(brush painted)(this Aires pit was a NIGHTMARE to make fit!)
A-6...(brush painted)
I'll do the seats later.
-
BlackSheep214
- Elite Member
- Posts: 13418
- Joined: Sun Apr 06, 2014 8:47 pm
Re: Quadruple Jet Threat
Fermis, that is an interesting way to create clear nav and tail beacon lights using clear sprues. How the heck do you get them to look like that and clear? What grit did you use to buff it clear? Can you give me pointers on doing those? I'd like to try my hand on a scrap F-16 kit.
“Who controls the skies, controls the fate of this Earth”
Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney
“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
Author unknown- 352nd Fighter Group, Blue-Nosed Bastards of Bodney
“Send one plane it’s a sortie; send two planes it’s a flight; send four planes it’s a test of airpower. - Richard Kohn
Re: Quadruple Jet Threat
I use Testors "sanding films", starting with the heaviest grit, working to the lightest(150-600). Then hit it with a rag wheel/Dremel.BlackSheep214 wrote:Fermis, that is an interesting way to create clear nav and tail beacon lights using clear sprues. How the heck do you get them to look like that and clear? What grit did you use to buff it clear? Can you give me pointers on doing those? I'd like to try my hand on a scrap F-16 kit.
-
Duke Maddog
- Elite Member
- Posts: 7669
- Joined: Tue Jun 03, 2014 11:22 am
- Location: Rowland Heights, CA
Re: Quadruple Jet Threat
Magnificent work Fermis! Man, I cannot keep up! I just hope to get mine finished to some level of quality, Keep going man, this is stunning work.
The Duke
Virtuoso of Miniatures
"Do you know what the chain of command is? It's the chain I get and beat you with 'till you understand who's in ruttin' command!"
-Jayne Cobb, Firefly Episode 2 "The Train Job"
We are modelers - the same in spirit, in hunger to insanely buy newly released kits, hustlers in hiding our stash from our better halves and experts in using garbage as replacements for after-market parts.
Virtuoso of Miniatures
"Do you know what the chain of command is? It's the chain I get and beat you with 'till you understand who's in ruttin' command!"
-Jayne Cobb, Firefly Episode 2 "The Train Job"
We are modelers - the same in spirit, in hunger to insanely buy newly released kits, hustlers in hiding our stash from our better halves and experts in using garbage as replacements for after-market parts.
Re: Quadruple Jet Threat
A superb selection of builds Fermis - loving the cockpit work. 
Stuart Templeton 'I may not be good but I'm slow...'
Re: Quadruple Jet Threat
Not a lot to show...but everybody got there wings!
-
speedgraflex
- Moderator
- Posts: 11358
- Joined: Fri Feb 10, 2017 11:08 pm
- Contact:
Re: Quadruple Jet Threat
Fermis, I read through your build thread several times before I caught that you brush painted the cockpits. Um, may I add a BRAVO to these comments... WOW. Inspiring.
Bruce / speedgraflex
Bruce / speedgraflex
Make more models!
Re: Quadruple Jet Threat
Thankya sir!speedgraflex wrote:Fermis, I read through your build thread several times before I caught that you brush painted the cockpits. Um, may I add a BRAVO to these comments... WOW. Inspiring.
Bruce / speedgraflex
The 6 and 14 were brush painted...both 18s got the pre-painted Eduard stuff though.